Beurer blodtrycksmätare handled bc 28

Beurer BC 28 är en helautomatisk, noggrann och lättanvänd blodtrycksmätare för handleden.

Beurer BC 28 - Wrist blood pressure monitor Manual

Included in delivery

Check that the exterior of the cardboard delivery packaging fryst vatten intact and man sure that all contents are present. Before use, ensure that there fryst vatten no visible damage to the device or accessories and that all packaging ämne has been removed.

If you have any doubts, do not use the device and contact your retailer or the specified Customer Service address.

1x Blood pressure monitor with cuff
2x 1.5 V LR03 AAA batteries
1x Storage box
1x Instructions for use

Signs and symbols

The following symbols are used in these instructions for use, on the packaging and on the type tallrik for the device and the accessories:

Intended use

The wrist blood pressure monitor serves as a non-invasive way of measuring and monitoring arterial blood pressure and pulse values in adults with wrist circumferences of 14 – 19.5 cm.

This allows you to quickly and easily measure your blood pressure and pulse, spara the measurements and display the development of the measurements. The recorded values are classified and evaluated graphically. You are also warned of possible existing cardiac arrhythmia.

Warning and safety notes

Notes on use

Read these instructions for use carefully and keep them for later use, be sure to man them accessible to other users and observe the kunskap they contain.

In beställning to ensure comparable values, always measure your blood pressure at the same time of day.
Do not take a measurement within 30 minutes of eating, drinking, smoking or exercising.
Before the första blood pressure measurement, man sure always to rest for about 5 minutes.
Furthermore, if you want to take several measurements in efterträdelse eller följd, man sure always to wait for at least 1 minute between the individual measurements.
Repeat the measurement if you are unsure of the measured value.
The measured values taken bygd you are for your data only – they are no substitute for a medical examination.

Discuss the measured values with your doctor and never base any medical decisions on them (e.g. medicines and their dosages).
Using the blood pressure monitor outside your home environment or whilst on the move (e.g. whilst traveling in a fordon, ambulance or helicopter, or whilst åtagande physical activity such as playing sport) can influence the measurement accuracy and cause incorrect measurements.
Do not use the blood pressure monitor on newborns or patients with pre-eclampsia.

We recommend consulting a doctor before using the blood pressure monitor during pregnancy.
In the case of restricted circulation on the ledd as a result of chronic or acute vascular diseases (including vascular constriction), the accuracy of the wrist measurement fryst vatten limited. In this case you should use an upper ledd blood pressure monitor instead.
This device fryst vatten not intended for use bygd people (including children) with restricted physical, sensory or mental skills or a lack of experience and/or a lack of knowledge, unless they are supervised bygd a individ who has responsibility for their safety or they receive instructions from this individ on how to use the device.
Beurer BC 28 User Manual View and Read online.
Supervise children around the device to ensure they do not play with it.
Cardiovascular diseases may lead to incorrect measurements or have a detrimental effect on measurement accuracy. The same also applies to very low blood pressure, diabetes, circulatory disorders and arrhythmias as well as chills or shaking.
The blood pressure monitor must not be used in connection with a high-frequency surgical unit.
Only use the device on people who have the specified wrist measurement for the device.
Please note that when inflating, the functions of the limb in question may be impaired.
During the blood pressure measurement, the blood circulation must not be stopped for an unnecessarily long time.

If the device malfunctions, remove the cuff from the arm.
Do not allow sustained pressure in the cuff or frequent measurements. The resulting restriction of the blood flow may cause injury.
Make sure that the cuff fryst vatten not placed on an ledd in which the arteries or veins are undergoing medical treatment, e.g.

intravascular tillgång or intravascular therapy, or an arteriovenous (AV) shunt.
Do not use the cuff on people who have undergone a mastectomy.
Do not place the cuff over wounds as this may cause further injury.
Place the cuff on your wrist only. Do not place the cuff on other parts of the body.
The blood pressure monitor can only be operated with batteries.
To conserve the batteries, the blood pressure monitor switches off automatically if you do not press any buttons for one minute.
The device fryst vatten only intended for the purpose described in these instructions for use.

The manufacturer fryst vatten not liable for damage resulting from improper or incorrect use.

Instructions for storage and maintenance

The blood pressure monitor fryst vatten made from noggrannhet and electronic components. The accuracy of the measured values and service life of the device depend on careful handling:
- Protect the device from impacts, humidity, dirt, marked temperature fluctuations and direkt sunlight.
- Do not drop the device.
- Do not use the device in the vicinity of strong electromagnetic fields and keep it away from radio systems or mobile telephones.
We recommend that the batteries be removed if the device will not be used for a prolonged period of time.

Notes on papper batteries

If your skin or eyes komma into contact with battery fluid, rinse the affected areas with vatten and seek medical assistance.
Choking hazard! Small children may swallow and choke on batteries.

Therefore, store batteries out of the reach of small children.
Observe the plus (+) and minus (-) polarity signs.
If a battery has leaked, put on protective handskar and clean the battery compartment with a dry cloth.
Protect batteries from excessive heat.
fara of explosion! Do not throw batteries into a fire.
Do not charge or short-circuit batteries.
If the device fryst vatten not to be used for a relatively long period, take the batteries out of the battery compartment.
Use identical or equivalent battery types only.
Always replace all batteries at the same time.
Do not use rechargeable batteries.
Do not disassemble, split or crush the batteries.

Notes on electromagnetic compatibility

The device fryst vatten suitable for use in all environments listed in these instructions for use, including domestic environments.
The use of the device may be limited in the presence of electromagnetic disturbances.

This could result in issues such as error messages or the failure of the display/device.
Avoid using this device directly next to other devices or stacked on top of other devices, as this could lead to faulty operation. If, however, it fryst vatten necessary to use the device in the manner stated, this device as well as the other devices must be monitored to ensure they are working properly.
The use of accessories other than those specified or provided bygd the manufacturer of this device can lead to an increase in electromagnetic emissions or a decrease in the device's electromagnetic immunity; this can result in faulty operation.
Failure to comply with the above can impair the performance of the device.

Device description

Display
Wrist cuff
Risk indicator
Start/stop button
Memory button M
Battery compartment lid

Information on the display

Systolic pressure
Risk indicator
Diastolic pressure
Calculated pulse rate
Cardiac arrhythmia emblem
Pulse tecken
User memory
Memory space number/ memory display for average value ( ), morning ( ), evening ( )
Battery replacement emblem
Time and date
Release air (arrow)

Initial use

Inserting the battery

Remove the battery compartment lid on the left side of the device.
Insert two 1.5 V micro (alkaline type LR03) batteries.
Make sure that the batteries are inserted the correct way round in accordance with the markings.

Do not use rechargeable batteries.
Carefully close the battery compartment lid igen. If the battery replacement emblem fryst vatten displayed, you can no längre perform any measurements and must replace all batteries.

Setting the hour format, date and time

It fryst vatten essential that you set the date and time. Otherwise, you will not be able to rädda your measured values correctly with a date and time and tillgång them igen later.

There are two different ways to tillgång the menu from which you can adjust the settings:

Before första use and after each time you replace the battery:
When inserting the batteries into the device you will be taken to the betydelsefull menu automatically.
If the batteries have already been inserted:
With the device switched off press and hold the START/STOP button for approx.
.
5 seconds.

In this menu you can adjust the following settings in succession:

Hour format

Press and hold the START/STOP button for 5 seconds or insert the batteries. The full display appears.
Select the desired hour format using the memory button M and confirm with the START/STOP button .

Date

The year flashes on the display.

Select the desired year using the memory button M and confirm with the START/STOP button .

The month flashes on the display.

Select the desired month with the memory button M and confirm with the START/ STOP button .

The day flashes on the display.

Select the desired day using the memory but-ton M and confirm with the START/STOP button .

If the hour format fryst vatten set as 12h, the day/month display sequence fryst vatten reversed.

Time

The hours flash on the display.

Select the desired hour using the memory button M and confirm with the START/ STOP button .

The minutes flash on the display.

Select the desired minute using the memory button M and confirm with the START/ STOP button .

Once all the uppgifter has been set, the device switches off automatically.

Usage

Ensure the device fryst vatten at room temperature before measuring.

Beurer BC 28 wrist blood pressure monitor.

The measurement can be performed on the left or right wrist.

Attaching the cuff

Expose your wrist. Ensure that the circulation of the ledd fryst vatten not hindered bygd tight clothing or similar.
Place the cuff on the inre of your wrist.
Fasten the cuff with the hook-and-loop fastener so that the upper end of the display fryst vatten approx.

1 cm below the heel of your hand.
The cuff must be fitted tightly around the wrist, but must not constrict.

Blood pressure may vary between the right and left ledd, which may mean that the measured blood pressure values are different. Always perform the measurement on the same arm.

If the values between the two arms are significantly different, please consult your doctor to determine which ledd should be used for the measurement.

Adopting the correct posture

Before the första blood pressure measurement, man sure always to rest for about 5 minutes.

Otherwise deviations can occur.
You can take the measurement while sitting or lying down. To take your blood pressure, man sure you are sitting comfortably with your arms and back leaning on something. Do not cross your legs. Place your feet flat on the ground.
Beurer BC 28 besitter ett klar display samt ger enstaka snabb samt bekväm mätning.
man sure to support your ledd and böj it. Always man sure that the cuff fryst vatten at heart level. Otherwise significant deviations can occur. Relax your ledd and the palm of your hand.
To avoid falsifying the measurement, it fryst vatten important to remain still during the measurement and not to speak.
Wait for at least 1 minute before taking another measurement.

Performing the blood pressure measurement

As described above, attach the cuff and adopt the posture in which you want to perform the measurement.

Press the START/STOP button to början the blood pressure monitor .

All displays will illuminate briefly.
The gods measured value fryst vatten dis-played and the blood pressure monitor automatically begins the measurement after 3 seconds.

You can cancel the measurement at any time bygd pressing the START/STOP button .

As soon as a pulse fryst vatten funnen, the pulse emblem will be displayed.

If you forget to vända off the device, it will switch off automatically after approx.

1 minute.
In this case too, the value fryst vatten stored in the selected or most recently used user memory. Wait for at least 1 minute before taking another measurement.

Evaluating results

Cardiac arrhythmia

This device can identify potential disruptions of the heart rhythm when measuring and, if necessary, indicates this after the measurement with the emblem .
This can be an indicator for arrhythmia.

Arrhythmia fryst vatten an illness in which the heart rhythm fryst vatten abnormal because of flaws in the bioelectrical struktur that regulates the heartbeat. The symptoms (skipped or premature heart beats, pulse being slow or too fast) can be caused bygd factors such as heart disease, age, physical make-up, excess stimulants, stress or lack of sova.

Helautomatisk blodtrycksmätning till handled.

Arrhythmia can only be determined through an examination bygd your doctor. If the tecken fryst vatten shown on the display after the measurement has been taken, repeat the measurement. Please ensure that you rest for 5 minutes beforehand and do not speak or move during the measurement.
If the tecken appears frequently, please consult your doctor.

Self-diagnosis and treatment based on the measurements can be dangerous. Always follow your doctor's instructions.

Risk indicator

The measurements can be classified and evaluated in accordance with the following table.
However, these standard values serve only as a general guideline, as the individual blood pressure varies in different people and different age groups etc.

It fryst vatten important to consult your doctor regularly for advice. Your doctor will tell you your individual values for normal blood pressure as well as the value above which your blood pressure fryst vatten classified as dangerous. The classification on the display and the scale on the device show which category the recorded blood pressure values fall into. If the values of systole and diastole fall into two different categories (e.g.

systole in the "High normal" category and diastole in the "Normal" category), the graphical classification on the device always shows the higher category; for the example given this would be "High normal".

Blood pressure value category	Systole (in mmHg)	Diastole (in mmHg)	Action
Level 3: severe hypertension	≥ 180	≥ 110	Seek medical attention
Level 2: moderate hypertension	160 – 179	100 – 109	Seek medical attention
Level 1: mild hypertension	140 – 159	90 – 99	Regular monitoring bygd doctor
High normal	130 – 139	85 – 89	Regular monitoring bygd doctor
Normal	120 – 129	80 – 84	Self-monitoring
Optimal	< 120	< 80	Self-monitoring

Source: WHO, 1999 (World Health Organization)

Saving, accessing and deleting measured values

User memory

The results of every successful measurement are stored tillsammans with the date and time.

The oldest measurement fryst vatten overwritten in the event of more than 60 measurements.

To retrieve the measurement, press the memory button M.

flashes on the display.

The average value of all saved measured values in this user memory fryst vatten displayed.
To change the user memory, press and hold the memory button M for approx.

2 seconds.

Average values

Press the memory button M.

flashes on the display.

The average value of the morning measurements for the gods 7 days fryst vatten displayed (morning: 5 a.m. – 9 a.m.).

Press the memory button M.

flashes on the display.

The average value of the evening measurements for the gods 7 days fryst vatten displayed (evening: 6 p.m.

– 8 p.m.).

Individual measured values

When you press the memory button M igen, the gods individual measurement fryst vatten displayed (in this example, measurement 03).
When you press the memory button M igen, you can view your individual measured values.
To switch the device off igen, press the START/ STOP button .

You can exit the menu at any time bygd pressing the START/STOP button .

Deleting measured values

To klar the betydelsefull user memory, you must first select a user memory.
Start the retrieval of the average measured values.
flashes on the display and the average value of all saved measured values in this user memory fryst vatten displayed.
Press and hold the memory button M and the START/STOP button for 5 seconds, depending on the user memory you are in.

All values of the current user memory are deleted and the device switches off.

Cleaning and maintenance

Clean the device and cuff carefully using a slightly damp cloth only.
Do not use any cleaning agents or solvents.
Under no circumstances hold the device and cuff beneath vatten, as this can cause liquid to enter and damage the device and cuff.
If you store the device and cuff, do not place heavy objects on the device and cuff.

Remove the batteries.

What if there are problems?

Technical specifications

Model no.	BC 28
Measurement method	Oscillometric, non-invasive blood pressure measurement on the wrist
Measurement range	Cuff pressure 0 – 300 mmHg, systolic 60 – 260 mmHg, diastolic 40 – 199 mmHg, pulse 40 – 180 beats/minute
Display accuracy	Systolic ± 3 mmHg, diastolic ± 3 mmHg, pulse ± 5% of the value shown
Measurement uncertainty	högsta. permissible standard deviation according to clinical testing: systolic 8 mmHg / diastolic 8 mmHg
Memory	2 x 60 memory spaces
Dimensions	L 84 mm x W 60 mm x H 29 mm
vikt	Approx. 92 g (without batteries, with cuff)
Cuff storlek	140 to 195 mm
Permissible operating conditions	+ 10°C to +40°C, ≤85% relative humidity (non-condensing)
Permissible storage conditions	-20°C to +50°C, ≤ 85% relative humidity, 800 –1050 hPa ambient pressure
Power supply	2 x 1.5-V AAA batteries
Battery life	For approx. 170 measurements, depending on levels of blood pressure and inflation pressure
Classification	Internal supply, IP22, no AP or APG, continuous operation, application part type BF

The serial number fryst vatten located on the device or in the battery compartment.
Technical upplysning fryst vatten subject to change without notification to allow for updates.

This device complies with the europeisk standard enstaka 60601-1-2 (compliance with CISPR 11, IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-8) and fryst vatten subject to special precautionary measures with regard to electromagnetic compatibility.

Please note that portable and mobile HF communication systems may interfere with this device.
The device complies with the EU Medical Devices Directive 93/42/EEC, the German Medical Devices Act (Medizinproduktgesetz) and the standards ett 1060-1 (Non-invasive sphygmomanometers – Part 1: General requirements), ett 1060-3 (Non-invasive sphygmomanometers – Part 3: Supplementary requirements for electro-mechanical blood pressure measuring systems) and IEC 80601-2-30 (Medical electrical redskap – Part 2 – 30: Particular requirements for the basic safety and essential performance of automated non-invasive sphygmomanometers).
The accuracy of this blood pressure monitor has been carefully checked and developed with regard to a long useful life.

If the device fryst vatten used for commercial medical purposes, it must be regularly tested for accuracy bygd appropriate means. Precise instructions for checking accuracy may be requested from the service address.

Documents / Resources

Download manual

Here you can download full pdf utgåva of manual, it may contain additional safety instructions, warranty data, FCC rules, etc.

Download Beurer BC 28 - Wrist blood pressure monitor Manual